Quality Assurance Measuring System Brochures

Brochures for bond, thickness, moisture, and more...

GreCon Quality Assurance Measuring Systems Brochures

Online Measuring Systems for the Panel Industry
The latest technology in quality assurance measuring systems providing accurate panelboard measurement of bonding, thickness, moisture, material distribution, weight per unit area, raw density, surface inspection, and panel strength.
Wireless Hot Press Temperature & Pressure ContiLog
Optimize your pressing process by measuring the development of gas pressure and mat temperature in any position within your press. The ContiLog is an online sensor that measures the mat conditions and records them while the board runs through the hot press. Influnces from upstream processes or product parameters on the pressing process can be immediately detected.
Laboratory Formaldehyde Emissions Analyzer GA 5000
The gas analysis method according to EN717-2 is a rapid formaldehyde emission testing procedure. Alternative test method approved by California Air Resources Board (CARB). Samples are placed in a 60°C chamber and air is pumped through into water bubblers. The water is tested using a spectrophotometer to determine the amount of formaldehyde emitted from the sample each hour.
Online Bond Analyzer UPU 2000
On-line defect monitoring allows for immediate adjustments to production as well as trend analysis to optimize production of pressing cycles. Ultrasonic transmitters and receivers scan passing panels, and a central processor provides on-line monitoring, statistical analysis and warning alarms of production defects.
Online Bond Analyzer UPU 5000
Measure the bond quality using GreCon Ultrasonic Camera with self calibration. The visualization software allows operators to adjust production process when blows are detected, bond quality is low, changes in moisture content, and production speed is to fast for target quality value.
Online Thickness Gauge DMR 5000
Rhomboidal wing is a mechanical protection and positioning system for contact measurement over the entire panel length at higher production speeds. The measuring heads are prepositioned just millimeters above the panel providing a shorter distance for closing the heads onto the panel for measurement allowing for faster production speeds.
Online Infrared Moisture Meter IR 5000
Inline moisture monitoring after the chip or fiber dryer, or at the blender or forming station, provides measured values of moist, dry, or glued material without the delay of taking samples to the lab. Immediate adjustments can be made to optimize production in the drying process.
Online Microwave Moisture Meter MWF 5000
The sensor surface is resistive and not sensitive to industrial conditions. The deep penetration of the microwave field into the material's internal moisture content allows for an accurate measuring result.
Online Panelboard Mat Scanner DIEFFENSOR
With high resolution scanning over the entire panelboard mat, the DIEFFENSOR system determines the weight per unit area and material distribution of fiber, chip or OSB mat. Exact graphical and numeric representations enable the operator to adjust the forming process to achieve consistent panel quality while the use of material and energy is optimized.
Online Insulation Mat Scanner DIEFFENSOR
The DIEFFENSOR recognizes form and mass of a foreign object and stores this image in 3-D graphics for evaluation at a later time. One example is hot spots, which are identified as foreign objects during the production of fiberglass and rock wool. These hot spots can cause damage to the product and the production line.
Online Weight Per Unit Area Gauge BWQ 5000
On-line, traversing measuring detects uneven spreading and provides accurate profile data for monitoring of tolerance deviance and reduction of raw material usage. The BWQ cross profile scanning of the mat after forming provides data on the mat properties prior to the pressing process.
Online Weight Per Unit Area Gauge BWS 5000
The online stationary system keeps the fixed weight per unit area in the measuring position, even with changing wood assortments and different chip sizes. A visualization computer shows the measured values and makes an easy parameterization of the system possible. The BWS 5000 is installed directly in the forming station or at the dosing or forming belt.
Online Raw Density Profile StenOgraph
determines the raw density profile directly after continuous presses. Thus, the operator is able to rectify the raw density profile and the related product features of MDF and particleboard during the pressing process. The result is an increased panel quality while material and energy costs are reduced.
Plug-Up Detection
Should the cyclone get blocked in the monitoring area, the infrared radiation is interrupted; the system will give an alarm, activate countermeasures, and the pneumatic system may be immediately shutdown or diverted. The blockage is minimized and can be quickly removed. Downstream filters are not affected, and a production interruption will be of short duration.
Online Panel Surface Inspection System Superscan
The SUPERSCAN system objectively inspects 100 percent of the press size wood based panels online at full production speed. Inspection of the press size panels allows for product quality analysis and permits quick adjustments of the production process. For the inspection of decorative wood based panels (laminate floorings, furniture panels, lacquered or printed panels) use the SUPERSCAN system.
Online Panel Weight Scale GS 5000
Fluctuations in the material distribution cause an increase in production costs while quality is reduced. The Online Board Scale GS 5000 makes an automatic monitoring of the material distribution and the panel weight possible. By an optional linkage with a GreCon thickness gauge, the average raw density and the weight distribution within the panels can also be calculated and used to optimize the process.
Laboratory Raw Density Profile Analyzer DA-X
A laboratory workstation, the DA-X measures raw density profiles of multiple panel samples to assure density production tolerances are being met. Includes a high accuracy weight scale and electronic caliper which automatically transfers panel data to database for profile analysis.
Laboratory Microwave Moisture Meter MWF 5000LM
For the production of PARTICLE, MDF, HDF and OSB boards, the moisture content of the finished panel is an important quality feature. To control the quality of the finished panels, a test sample of 5 cm x 5 cm, sawn out of a finished panel, is measured in the laboratory.
Laboratory Panel Strength LabRob
The mechanical quality features of wood based panels can be easily and precisely determined. Measurement can be carried out for the internal bond strength supplying results within a few minutes.

Contact Information

Call Us: (503) 641-7731
Quote Request

Quality Assurance Measuring Systems.

Optimize energy and resources while maximizing production and profits.